Merge tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "I2C has mainly cleanups this time and a few driver improvements.

  Because a lot of developers were on holidays (including myself) it was
  a good timing to apply lots of cleanups which would normally cause
  merge conflicts with other floating patches. Extra thanks go to Andi
  Shyti who backed me up when I was on a four week hiatus. This is also
  the reason that some patches were commited later than ideal"

* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
  i2c: at91: Use dev_err_probe() instead of dev_err()
  I2C: ali15x3: Do PCI error checks on own line
  i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
  i2c: designware: Add support for recovery when GPIO need pinctrl
  i2c: mlxcpld: Add support for extended transaction length
  i2c: mlxcpld: Allow driver to run on ARM64 architecture
  i2c: nforce2: Do PCI error check on own line
  i2c: sis5595: Do PCI error checks on own line
  i2c: qcom-cci: Fix error checking in cci_probe()
  i2c: muxes: pca954x: Add regulator support
  i2c: muxes: pca954x: Add MAX735x/MAX736x support
  dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
  dt-bindings: i2c: pca954x: Correct interrupt support
  i2c: pnx: Use devm_platform_get_and_ioremap_resource()
  i2c: pxa: Use devm_platform_get_and_ioremap_resource()
  i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
  i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
  i2c: st: Use devm_platform_get_and_ioremap_resource()
  i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
  i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
  ...

Author: torvalds

Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml

@@ -48,6 +48,9 @@ properties:
     default: 16
     enum: [2, 4, 8, 16, 32, 64, 128, 256]
 
+  power-domains:
+    maxItems: 1
+
 required:
   - compatible
   - reg

Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt

@@ -0,0 +1,135 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/i2c-arb-gpio-challenge.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: GPIO-based I2C Arbitration Using a Challenge & Response Mechanism
+
+maintainers:
+  - Doug Anderson <dianders@chromium.org>
+  - Peter Rosin <peda@axentia.se>
+
+description: |
+  This uses GPIO lines and a challenge & response mechanism to arbitrate who is
+  the master of an I2C bus in a multimaster situation.
+
+  In many cases using GPIOs to arbitrate is not needed and a design can use the
+  standard I2C multi-master rules.  Using GPIOs is generally useful in the case
+  where there is a device on the bus that has errata and/or bugs that makes
+  standard multimaster mode not feasible.
+
+  Note that this scheme works well enough but has some downsides:
+   * It is nonstandard (not using standard I2C multimaster)
+   * Having two masters on a bus in general makes it relatively hard to debug
+     problems (hard to tell if i2c issues were caused by one master, another,
+     or some device on the bus).
+
+  Algorithm:
+  All masters on the bus have a 'bus claim' line which is an output that the
+  others can see. These are all active low with pull-ups enabled.  We'll
+  describe these lines as:
+   * OUR_CLAIM: output from us signaling to other hosts that we want the bus
+   * THEIR_CLAIMS: output from others signaling that they want the bus
+
+  The basic algorithm is to assert your line when you want the bus, then make
+  sure that the other side doesn't want it also.  A detailed explanation is
+  best done with an example.
+
+  Let's say we want to claim the bus.  We:
+  1. Assert OUR_CLAIM.
+  2. Waits a little bit for the other sides to notice (slew time, say 10
+     microseconds).
+  3. Check THEIR_CLAIMS.  If none are asserted then the we have the bus and we
+     are done.
+  4. Otherwise, wait for a few milliseconds and see if THEIR_CLAIMS are released.
+  5. If not, back off, release the claim and wait for a few more milliseconds.
+  6. Go back to 1 (until retry time has expired).
+
+properties:
+  compatible:
+    const: i2c-arb-gpio-challenge
+
+  i2c-parent:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      The I2C bus that this multiplexer's master-side port is connected to.
+
+  our-claim-gpios:
+    maxItems: 1
+    description:
+      The GPIO that we use to claim the bus.
+
+  slew-delay-us:
+    default: 10
+    description:
+      Time to wait for a GPIO to go high.
+
+  their-claim-gpios:
+    minItems: 1
+    maxItems: 8
+    description:
+      The GPIOs that the other sides use to claim the bus.  Note that some
+      implementations may only support a single other master.
+
+  wait-free-us:
+    default: 50000
+    description:
+      We'll give up after this many microseconds.
+
+  wait-retry-us:
+    default: 3000
+    description:
+      We'll attempt another claim after this many microseconds.
+
+  i2c-arb:
+    type: object
+    $ref: /schemas/i2c/i2c-controller.yaml
+    unevaluatedProperties: false
+    description:
+      I2C arbitration bus node.
+
+required:
+  - compatible
+  - i2c-arb
+  - our-claim-gpios
+  - their-claim-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c-arbitrator {
+        compatible = "i2c-arb-gpio-challenge";
+        i2c-parent = <&i2c_4>;
+
+        our-claim-gpios = <&gpf0 3 GPIO_ACTIVE_LOW>;
+        their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
+        slew-delay-us = <10>;
+        wait-retry-us = <3000>;
+        wait-free-us = <50000>;
+
+        i2c-arb {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            sbs-battery@b {
+                compatible = "sbs,sbs-battery";
+                reg = <0xb>;
+                sbs,poll-retry-count = <1>;
+            };
+
+            embedded-controller@1e {
+                compatible = "google,cros-ec-i2c";
+                reg = <0x1e>;
+                interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+                interrupt-parent = <&gpx1>;
+                pinctrl-names = "default";
+                pinctrl-0 = <&ec_irq>;
+                wakeup-source;
+            };
+        };
+    };

Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.yaml

@@ -4,21 +4,29 @@
 $id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
-title: NXP PCA954x I2C bus switch
+title: NXP PCA954x I2C and compatible bus switches
 
 maintainers:
   - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
 
 description:
-  The binding supports NXP PCA954x and PCA984x I2C mux/switch devices.
-
-allOf:
-  - $ref: /schemas/i2c/i2c-mux.yaml#
+  The NXP PCA954x and compatible devices are I2C bus
+  multiplexer/switches that share the same functionality
+  and register layout.
+  The devices usually have 4 or 8 child buses, which are
+  attached to the parent bus by using the SMBus "Send Byte"
+  command.
 
 properties:
   compatible:
     oneOf:
       - enum:
+          - maxim,max7356
+          - maxim,max7357
+          - maxim,max7358
+          - maxim,max7367
+          - maxim,max7368
+          - maxim,max7369
           - nxp,pca9540
           - nxp,pca9542
           - nxp,pca9543
@@ -59,10 +67,34 @@ properties:
     description: if present, overrides i2c-mux-idle-disconnect
     $ref: /schemas/mux/mux-controller.yaml#/properties/idle-state
 
+  vdd-supply:
+    description: A voltage regulator supplying power to the chip. On PCA9846
+      the regulator supplies power to VDD2 (core logic) and optionally to VDD1.
+
 required:
   - compatible
   - reg
 
+allOf:
+  - $ref: /schemas/i2c/i2c-mux.yaml#
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              enum:
+                - maxim,max7367
+                - maxim,max7369
+                - nxp,pca9542
+                - nxp,pca9543
+                - nxp,pca9544
+                - nxp,pca9545
+    then:
+      properties:
+        interrupts: false
+        "#interrupt-cells": false
+        interrupt-controller: false
+
 unevaluatedProperties: false
 
 examples:
@@ -74,11 +106,13 @@ examples:
         #size-cells = <0>;
 
         i2c-mux@74 {
-            compatible = "nxp,pca9548";
+            compatible = "nxp,pca9545";
             #address-cells = <1>;
             #size-cells = <0>;
             reg = <0x74>;
 
+            vdd-supply = <&p3v3>;
+
             interrupt-parent = <&ipic>;
             interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
             interrupt-controller;