riscv: dts: starfive: Add mmc nodes on VisionFive 2 board

Add the mmc nodes for the StarFive JH7110 SoC.
Set mmc0 node to emmc and set mmc1 node to sd.

Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

Author: littleqyp

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi

@@ -17,6 +17,8 @@
 		i2c2 = &i2c2;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
 		serial0 = &uart0;
 	};
 
@@ -201,6 +203,35 @@
 	status = "okay";
 };
 
+&mmc0 {
+	max-frequency = <100000000>;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	cap-mmc-hw-reset;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+	status = "okay";
+};
+
+&mmc1 {
+	max-frequency = <100000000>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	broken-cd;
+	cap-sd-highspeed;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	status = "okay";
+};
+
 &qspi {
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -306,6 +337,71 @@
 		};
 	};
 
+	mmc0_pins: mmc0-0 {
+		 rst-pins {
+			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <PINMUX(64, 0)>,
+				 <PINMUX(65, 0)>,
+				 <PINMUX(66, 0)>,
+				 <PINMUX(67, 0)>,
+				 <PINMUX(68, 0)>,
+				 <PINMUX(69, 0)>,
+				 <PINMUX(70, 0)>,
+				 <PINMUX(71, 0)>,
+				 <PINMUX(72, 0)>,
+				 <PINMUX(73, 0)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+		};
+	};
+
+	mmc1_pins: mmc1-0 {
+		clk-pins {
+			pinmux = <GPIOMUX(10, GPOUT_SYS_SDIO1_CLK,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <GPIOMUX(9, GPOUT_SYS_SDIO1_CMD,
+					     GPOEN_SYS_SDIO1_CMD,
+					     GPI_SYS_SDIO1_CMD)>,
+				 <GPIOMUX(11, GPOUT_SYS_SDIO1_DATA0,
+					      GPOEN_SYS_SDIO1_DATA0,
+					      GPI_SYS_SDIO1_DATA0)>,
+				 <GPIOMUX(12, GPOUT_SYS_SDIO1_DATA1,
+					      GPOEN_SYS_SDIO1_DATA1,
+					      GPI_SYS_SDIO1_DATA1)>,
+				 <GPIOMUX(7, GPOUT_SYS_SDIO1_DATA2,
+					     GPOEN_SYS_SDIO1_DATA2,
+					     GPI_SYS_SDIO1_DATA2)>,
+				 <GPIOMUX(8, GPOUT_SYS_SDIO1_DATA3,
+					     GPOEN_SYS_SDIO1_DATA3,
+					     GPI_SYS_SDIO1_DATA3)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+
 	spi0_pins: spi0-0 {
 		mosi-pins {
 			pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,

arch/riscv/boot/dts/starfive/jh7110.dtsi

@@ -821,6 +821,38 @@
 				 <&syscrg JH7110_SYSRST_WDT_CORE>;
 		};
 
+		mmc0: mmc@16010000 {
+			compatible = "starfive,jh7110-mmc";
+			reg = <0x0 0x16010000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_SDIO0_AHB>,
+				 <&syscrg JH7110_SYSCLK_SDIO0_SDCARD>;
+			clock-names = "biu","ciu";
+			resets = <&syscrg JH7110_SYSRST_SDIO0_AHB>;
+			reset-names = "reset";
+			interrupts = <74>;
+			fifo-depth = <32>;
+			fifo-watermark-aligned;
+			data-addr = <0>;
+			starfive,sysreg = <&sys_syscon 0x14 0x1a 0x7c000000>;
+			status = "disabled";
+		};
+
+		mmc1: mmc@16020000 {
+			compatible = "starfive,jh7110-mmc";
+			reg = <0x0 0x16020000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_SDIO1_AHB>,
+				 <&syscrg JH7110_SYSCLK_SDIO1_SDCARD>;
+			clock-names = "biu","ciu";
+			resets = <&syscrg JH7110_SYSRST_SDIO1_AHB>;
+			reset-names = "reset";
+			interrupts = <75>;
+			fifo-depth = <32>;
+			fifo-watermark-aligned;
+			data-addr = <0>;
+			starfive,sysreg = <&sys_syscon 0x9c 0x1 0x3e>;
+			status = "disabled";
+		};
+
 		gmac0: ethernet@16030000 {
 			compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
 			reg = <0x0 0x16030000 0x0 0x10000>;