Merge patch series "can: m_can: set init flag earlier in probe"

This series fixes problems in the m_can_pci driver found on the Intel
Elkhart Lake processor.

Link: https://patch.msgid.link/e247f331cb72829fcbdfda74f31a59cbad1a6006.1728288535.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Author: marckleinebudde

drivers/net/can/m_can/m_can.c

@@ -1220,20 +1220,32 @@ static void m_can_coalescing_update(struct m_can_classdev *cdev, u32 ir)
 static int m_can_interrupt_handler(struct m_can_classdev *cdev)
 {
 	struct net_device *dev = cdev->net;
-	u32 ir;
+	u32 ir = 0, ir_read;
 	int ret;
 
 	if (pm_runtime_suspended(cdev->dev))
 		return IRQ_NONE;
 
-	ir = m_can_read(cdev, M_CAN_IR);
+	/* The m_can controller signals its interrupt status as a level, but
+	 * depending in the integration the CPU may interpret the signal as
+	 * edge-triggered (for example with m_can_pci). For these
+	 * edge-triggered integrations, we must observe that IR is 0 at least
+	 * once to be sure that the next interrupt will generate an edge.
+	 */
+	while ((ir_read = m_can_read(cdev, M_CAN_IR)) != 0) {
+		ir |= ir_read;
+
+		/* ACK all irqs */
+		m_can_write(cdev, M_CAN_IR, ir);
+
+		if (!cdev->irq_edge_triggered)
+			break;
+	}
+
 	m_can_coalescing_update(cdev, ir);
 	if (!ir)
 		return IRQ_NONE;
 
-	/* ACK all irqs */
-	m_can_write(cdev, M_CAN_IR, ir);
-
 	if (cdev->ops->clear_interrupts)
 		cdev->ops->clear_interrupts(cdev);
 
@@ -1695,6 +1707,14 @@ static int m_can_dev_setup(struct m_can_classdev *cdev)
 		return -EINVAL;
 	}
 
+	/* Write the INIT bit, in case no hardware reset has happened before
+	 * the probe (for example, it was observed that the Intel Elkhart Lake
+	 * SoCs do not properly reset the CAN controllers on reboot)
+	 */
+	err = m_can_cccr_update_bits(cdev, CCCR_INIT, CCCR_INIT);
+	if (err)
+		return err;
+
 	if (!cdev->is_peripheral)
 		netif_napi_add(dev, &cdev->napi, m_can_poll);
 
@@ -1746,11 +1766,7 @@ static int m_can_dev_setup(struct m_can_classdev *cdev)
 		return -EINVAL;
 	}
 
-	/* Forcing standby mode should be redundant, as the chip should be in
-	 * standby after a reset. Write the INIT bit anyways, should the chip
-	 * be configured by previous stage.
-	 */
-	return m_can_cccr_update_bits(cdev, CCCR_INIT, CCCR_INIT);
+	return 0;
 }
 
 static void m_can_stop(struct net_device *dev)

drivers/net/can/m_can/m_can.h

@@ -99,6 +99,7 @@ struct m_can_classdev {
 	int pm_clock_support;
 	int pm_wake_source;
 	int is_peripheral;
+	bool irq_edge_triggered;
 
 	// Cached M_CAN_IE register content
 	u32 active_interrupts;

drivers/net/can/m_can/m_can_pci.c

@@ -127,6 +127,7 @@ static int m_can_pci_probe(struct pci_dev *pci, const struct pci_device_id *id)
 	mcan_class->pm_clock_support = 1;
 	mcan_class->pm_wake_source = 0;
 	mcan_class->can.clock.freq = id->driver_data;
+	mcan_class->irq_edge_triggered = true;
 	mcan_class->ops = &m_can_pci_ops;
 
 	pci_set_drvdata(pci, mcan_class);